Bye Bye Summer

It’s a wet, chill afternoon in late August. Lightning bolts have lit the sky and thunder has rolled around the Chiltern Hills. The epoxy is taking ages to set and I suppose I should light the stove. But the boat is too close to it and the epoxy is soft – it’s best not to move her. I know –  I’ll write the blog, it’s been a while.  Many thanks to all you who have expressed support (if not sympathy!).  And please accept my deepest apologies, I’ve been forgetting to approve your comments. 1

Martyjn – the now not so new owner of Riff Raff – sent a photo of her from somewhere in Holland and said it was a good job that I’d thought about the waterline and the ballast tanks. It was but I fear my solution to the problem may have been a little cavalier – there were gaps and holes in insulation I used2 so she may not floaton an even keel when the tanks are fully loaded.

The retired anaesthetist thought I was being artistic in the build of the boat – I’m too sure why

Patmf likes the idea of a boat builder making his own tools – well, Pat, if you read on there’ll another one on display in this edition.

But, as usual, I digress, although less tangentially than usual.

I’ve checked. Blog time3 is still set in July, so it’s overdue for an update. Sadly, very little seems to have happened in the month. I’ve fitted the stem post. I’ve coated the main forward locker with white coloured epoxy – at least it might now be possible to see stuff in it. I’ve bought a pair of bronze rowlocks (very posh). A samson post has been fitted just ahead of the locker. The engine mounts have been glued in place. I’ve trial fitted the bulwarks and attempted to make two scarf joints. I’ve discovered that bending the bulwark timber round the transom is impossible…..

That’s it. I’ve also replaced my 8 yearold  obsolete laptop with a new one. WWW no longer stands for world wide wait but why does getting the files from the old one, and getting it to remember all those passwords take so long?) . And I’ve attemptd to assist the cabin boy5 with his A level Maths……..

So, I suppose, you might like to know the detail. I think I’ve some photos.

The stem post was provided to me with the flat pack of plywood – machined out of (I assume) Utilie hardwood. I had already trial fitted it when I put in place the keel strips7 and also prepared a flat bed of epoxy on the prow so that the stem post would line up with the center line of the boat. All I had to do was mix up some epoxy, line everything up and push the stem post into place….

The laser level was brought out of the cupboard…

The laser level was fired up – but the batteries were flat. A trip to the local garage supplied new ones. The boat wasn’t level but I found a setting on the laser that allowed me to align the laser with the centre line none the less. The bottom end of the stem post had been shaped to match the hardwood at the foot of the stem and required careful positioning to make the join almost perfect. But how to hold it in place whilst the epoxy set? The weight of the post caused it to slip slowly downwards dispite the efforts of a G clamp over the top. Eventually I hit on the idea of glueing a small strip of plywood across the inside face of the post using an instant glue.8 This allowed the post to hang on the plywood bow in the right place and the G clamp then completed the fix. The epoxy was mixed up, slathered into place and, eight hours later the stem was complete.

Then followed the samson post. “Get a large square section of utilie and epoxy it to the forward side of the forward bulkhead” I was told. How large? “Large enough.” The biggest length I had was about 40mm x 30mm. So two were glued together and then sawn square. The laser pointer came into play again to place the post vertically on the bulkhead and it was epoxied into place. Then I spotted the obvious fault. OOPs, I hadn’t take equal amounts either side of the seam, so the Samson post has an obvious off centre join – but at least it’s lined across the boat, rather than fore and aft.9

The motor slide mounts in the well at the stern were postioned using a simple jig which had been “laser cut”10 somewhere in Scotland. These mounts have to be reasonably aligned so that the motor can slide up and down out of and into the water as required. After a little jiggling about and more instant glue, the jig was held in position and the utilie mounts were glued into place.

Motor slide mounts held in position by laser cut plywood jig

I sense that I’m in the home straight. Only the gunwales to fix in place, and then the deck and the rowlocks and a grid to cover the bilge well, the fairing of the top plank and the deck and the painting…

But I’m getting ahead of myself. The gunwale, that strip of wood that runs along the ede of the deck and plank three needed to be over 4.5 metres long. My timber was only three and a bit. This called for a scarf joint – a long diagonal joint in the timber. I knew I’ve never cut that unaided by hand so; it called for another jig. You’ll have to wait to discover how it worked out.

Notes

  1. There done it. You can see them all now going back to the beginning of the project.
  2. See previous post “Imagination and Bloody Mindedness” for the full story
  3. This is a derivation of Terry Pratchet’s L space where all libraries are interconnected in space and time and you enter a library and lose all awareness of time and space. AS was outlined in both dimensions. Blog time was fully explained in a previous post but that itslf is now lost in the past. In summary blog time is time past, when the author last put finers to keys.4
  4. The new computer and the old remote kybaord are  kybord  are not getting on too well. Somhow letters kep eing missed. It’s as if there’s Brmuda trianleof some sort, covering an area of the keyboard bounded (and including) etgvxs where, every now aain, ky presses are not rcognised. I think it might be related to coffee spill a week or so ago…..
  5. Well he was when he helped me  launch Vagabond several years ago. H’s now a 17 yar old, who is taller than me. 6
  6. Not difficult
  7. See an earlier post “Real Rough Carpentry”
  8. Where would I have been without instant glue and accelerators? With more skin on my fingers.
  9. This was entirely by chance.
  10. High tech precision stuff.

One thought on “Bye Bye Summer”

  1. Love you Riffa ! you have to rate highly when you can right with an accent !!I was fortunate enough to live in your marvellous country for two years when I was young tear away and I just loved the accents and have said to my fellow Aussies, when the Poms loose there accents we are in deep sh…t! as the world would have lost there sense of humour!!
    Oh and the sailing boats coming on nicely.
    keep well mate!

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.